Bottom Bulk Carrier
HPT Series High-Efficiency Hydraulic Cone Crusher combines crushing stroke with crushing chamber perfectly, which makes capacity improved and efficiency increased. Besides, hydraulic lubrication control system helps bearing of hydraulic cone crusher get double protection.
Efficiency increased by 5%-15%, Capacity improved by 35%-60%
Applications:
Aggregate field,concrete mixing plant,dry mortar plant desulfurization,quartz sand,etc.
Capacity: 55-700T/H
Input size: 76-320mm
Performance Advantages
advanced crushing principle and technical data, reliable operation and low operation cost. All parts of the crusher have anti-wearing protection, which can make the life time of spare parts increased by 30% and the maintenance cost decreased to the lowest. The crusher avoids the disadvantages of impact crusher like low average crushing ratio, large energy consumption, fast abrasion of blow bar, impact plate and lining board.
The crusher adopts between-layer pressuring crushing principle and suitable turning speed, not the traditional single particle crushing principle. The special crushing cavity can make the crusher crush materials selectively, thus the proportion of fine product and product of cubic shape is increased distinctly and product of lump size is decreased by a large extent.
Unique design of thin oil lubrication system prolongs life time of the crusher, high performance and not touchable labyrinth airproof part block off dust and remove common disorders like mixture of oil and water in spring cone crusher.
Discharge opening is adjusted by hydraulic device and overload protection makes performance of the crusher increased by a large extent, maintenance and operation are easier, repairing time is shorter.; the bidirectional metal releasing hydraulic vat makes slab pass through crushing cavity；the crusher can discharges material automatically when the hydraulic device works under the condition of iron passing and instantaneous overloading, thus there is no trouble of stopping the crusher to discharge material by hand.
It only need change fixed cone lining board and movable cone lining board; , the type of crushing cavity can be changed from standard coarse cavity to short head fine cavity, which can meet various kinds of requirements.
all parts of HPT series of cone crusher can be assembled, disassembled and repaired from the top and side part, including the fixed cone and movable cone. If change, no need to disassemble the crusher body and fasten the bolts. Hydraulic motor makes the performance of crusher better.
Specifications
Hot Sale: patented technology, high productivity, environmental protection and energy saving
FAQ
Does the PMD New-Generation Permanent-Magnet Direct-Drive Intelligent European Grinding Mill permanent-magnet motor need special maintenance?
The PMD New-Generation Permanent-Magnet Direct-Drive Intelligent European Grinding Mill permanent-magnet motor has high protection and sealed structure; daily care is just keeping cooling ducts clean and monitoring winding temperature and current. With n
hat is the mechanism for twin‑shaft kiln achieving NOx ≤300 mg/m³ without dedicated denitrification equipment?
Thermal‑NOx formation is restrained by low‑temperature combustion‑air plus short‑flame design. Combustion‑air is pre‑heated by ore inside regenerative‑shaft without reaching extreme peak‑temperature. Short‑flame mode suppresses flame‑peak‑temperature, and thermal‑NOx heavily depends on over‑high‑flame‑temperature. Alternating co‑current calcination eliminates local hot‑spots for further NOx reduction. If fuel contains high nitrogen content, combustion optimization has limitation; denitrification facility shall be evaluated under that circumstance.
What crushing stage does HPT hydraulic cone crusher apply to?
HPT multi‑cylinder hydraulic cone crusher is designed for secondary and tertiary crushing, receiving feed from jaw crushers to produce high‑quality manufactured sand and aggregates. It suits medium‑hard and hard ores and is not intended for large l
What are the features of the MTW European Type Trapezium Mill analyzer?
The MTW European Type Trapezium Mill uses a large-inclination impeller analyzer with high classification precision and large air handling. The cage rotor quickly separates qualified fines while coarse returns for re-grinding, giving narrow size distribut
What is the maximum allowable inlet temperature for the dryer?
Small single‑drum dryer allows max inflow temperature ≤700℃; medium‑large single‑drum (≥φ1500) ≤800℃; three‑tube dryer runs at 700‑750℃. Do not keep full‑limit temperature in real operation; avoid material over‑burning according to material heat resistance. Excessive temperature accelerates high‑temperature oxidation of drum and lifters and shortens wearing‑part service life. Operators shall strictly control heating parameters.
What negative impacts are brought by large feed drop height for S5X circular vibrating screen and how to mitigate them?
Excessive drop height from crusher causes violent material impact, accelerating mesh cracking and local fatigue damage of screen box. One‑sided impact leads to uneven material distribution, reduces screening efficiency and raises noise level. Install b
WhatsApp
Leave message